Mô-đun sạc pin lithium 18650 Pin lithium 5V1A HW-107 1A có bảo vệ
18.000
₫ 9.000
Sản phẩm Mô-đun sạc pin lithium 18650 Pin lithium 5V1A HW-107 1A có bảo vệ đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 18.000 xuống còn ₫ 9.000, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Mô-đun sạc pin lithium 18650 Pin lithium 5V1A HW-107 1A có bảo vệ
Features:
This module is used for single-cell lithium or lithium multi-section parallel, charging ports can take power from USB.
It can be used for voltage 3.6 3.7V, etc. 18650, polymer and other lithium battery charge and discharge protection.
Charge module- Linear charging.
It has MICRO USB female.
It still retain the input voltage wiring solder joints, can be very convenient to DIY
Specifications:
Type: Voltage Regulator
Apply: 18650 Lithium Battery
Current:1A adjustable.
Charge precision:1.5%.
Input voltage:4.5V-5.5V.
Full charge voltage:4.2V.
Led indicator:red is charging Green is full charged.
Input interface:micro USB.
Work temperature: -10℃ to +85℃.
Size: 27X17mm.
Package Included:
1 x 5V Micro USB 1A 18650 Lithium Battery Charging Board Charger Module
NOTE:
Only one 18650 batteries (6000mAh) you can charge with this charger in parallel at the same time
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protective function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.
NOTE:
Only one 18650 batteries (6000mAh) you can charge with this charger in parallel at the same time
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protective function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.
Features:
This module is used for single-cell lithium or lithium multi-section parallel, charging ports can take power from USB.
It can be used for voltage 3.6 3.7V, etc. 18650, polymer and other lithium battery charge and discharge protection.
Charge module- Linear charging.
It has MICRO USB female.
It still retain the input voltage wiring solder joints, can be very convenient to DIY
Specifications:
Type: Voltage Regulator
Apply: 18650 Lithium Battery
Current:1A adjustable.
Charge precision:1.5%.
Input voltage:4.5V-5.5V.
Full charge voltage:4.2V.
Led indicator:red is charging Green is full charged.
Input interface:micro USB.
Work temperature: -10℃ to +85℃.
Size: 27X17mm.
Package Included:
1 x 5V Micro USB 1A 18650 Lithium Battery Charging Board Charger Module
NOTE:
Only one 18650 batteries (6000mAh) you can charge with this charger in parallel at the same time
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protective function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.
NOTE:
Only one 18650 batteries (6000mAh) you can charge with this charger in parallel at the same time
1. Ampere meter can only be connected to 5v input end of the module.
2. It is better that the charging current is 37% of the battery capacity. If you charge to the battery of 1000mAH, current of 400 is enough.
3. The connection wire should not be too thick.
4. Make sure the connect point is good.
5. If the input voltage is too high, like 5.2v, the current will be less than 1000mA, it is normal. It is protective function, auto-substract the charging current to avoid burn damage to chip.
6. NO Reveral polarity.
Sản Phẩm Liên Quan
HOT
HOT
THÙNG PC WORKSTATION E5 2678V3 RAM 32GB - 64GB
₫ 15.550.000
HOT
HOT
HOT
lenovo y410 cũ
₫ 350.000
HOT
vga gt705 1gb d3 lắp cây đồng bộ và pc
₫ 500.000