Mô-Đun Điều Khiển Micro 7 Kênh Max7219 Led Matrix 8 Số 3.3v 5v Cho Arduino
₫ 40.100
Sản phẩm Mô-Đun Điều Khiển Micro 7 Kênh Max7219 Led Matrix 8 Số 3.3v 5v Cho Arduino đang được mở bán với mức giá siêu tốt khi mua online, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
[Vật Tư & Linh Kiện] "MAX7219 digital tube display control module
MAX7219 is an integrated serial input/output common-cathode display driver. It connects a microprocessor and an 8-digit 7-segment digital LED display. It can also connect to a bar graph display or 64 independent LEDs. It includes an on-chip B-type BCD encoder, multiple scanning loops, segment word drivers, and an 8*8 static RAM to store each data. Only one external register is used to set the segment current of each LED.
A convenient four-wire serial interface can be connected to all general-purpose microprocessors. Each data can be addressed without rewriting all the displays when updating. MAX7219 also allows users to select encoding or not encoding for each data.
The entire device includes a 150μA low-power shutdown mode, analog and digital brightness control, a scan limit register allowing users to display 1-8 bits of data, and a detection mode that allows all LEDs to emit light.
Only need 3 IO ports to drive 8-bit digital tube! No flicker when the digital tube displays! Support cascading! The display effect is shown in the figure below:
The digital tube and the PCB board are connected by 2.54mm pitch round hole pin headers, which can easily replace the digital tube!
The four corners of the PCB board are fixed with copper studs, which can effectively prevent accidents such as short circuits.
The digital tube is a 0.36 inch 4-in-one common cathode digital tube
This module is compatible with 5V/3.3V single chip microcomputer (51/AVR/STM32...)
Wiring instructions (take the provided program as an example, you can connect any IO port, just modify the port definition in the program):
VCC→5V
GND→GND
DIN →P00
CS →P01
CLK→P02
Precautions:
1. Don't connect VCC and GND reversely, so as not to burn the chip
2.51 The P0 port of the microcontroller needs to be connected to a pull-up resistor. If your microcontroller is not connected to a pull-up resistor, you can connect the data line to other ports" Liên hệ Zalo Mạnh Cường : 0356565178 để giải đáp mọi thắc mắc liên quan tới sản phẩm, dịch vụ của cửa hàng [Vật Tư & Linh Kiện] Sếp
MAX7219 is an integrated serial input/output common-cathode display driver. It connects a microprocessor and an 8-digit 7-segment digital LED display. It can also connect to a bar graph display or 64 independent LEDs. It includes an on-chip B-type BCD encoder, multiple scanning loops, segment word drivers, and an 8*8 static RAM to store each data. Only one external register is used to set the segment current of each LED.
A convenient four-wire serial interface can be connected to all general-purpose microprocessors. Each data can be addressed without rewriting all the displays when updating. MAX7219 also allows users to select encoding or not encoding for each data.
The entire device includes a 150μA low-power shutdown mode, analog and digital brightness control, a scan limit register allowing users to display 1-8 bits of data, and a detection mode that allows all LEDs to emit light.
Only need 3 IO ports to drive 8-bit digital tube! No flicker when the digital tube displays! Support cascading! The display effect is shown in the figure below:
The digital tube and the PCB board are connected by 2.54mm pitch round hole pin headers, which can easily replace the digital tube!
The four corners of the PCB board are fixed with copper studs, which can effectively prevent accidents such as short circuits.
The digital tube is a 0.36 inch 4-in-one common cathode digital tube
This module is compatible with 5V/3.3V single chip microcomputer (51/AVR/STM32...)
Wiring instructions (take the provided program as an example, you can connect any IO port, just modify the port definition in the program):
VCC→5V
GND→GND
DIN →P00
CS →P01
CLK→P02
Precautions:
1. Don't connect VCC and GND reversely, so as not to burn the chip
2.51 The P0 port of the microcontroller needs to be connected to a pull-up resistor. If your microcontroller is not connected to a pull-up resistor, you can connect the data line to other ports" Liên hệ Zalo Mạnh Cường : 0356565178 để giải đáp mọi thắc mắc liên quan tới sản phẩm, dịch vụ của cửa hàng [Vật Tư & Linh Kiện] Sếp
Sản Phẩm Liên Quan
HOT
Bikini hàng Âu
₫ 400.000
HOT
Bikini Thái quả ngang chấm bi
₫ 350.000
HOT
Bikini made in Thailand
₫ 350.000
HOT
Bikini Thái
₫ 300.000
HOT
Bikini OKISS- QCXK
₫ 400.000
HOT
Bikini xuất Âu
₫ 300.000