Mô Đun Điều Khiển Động Cơ Bước 8051 Arduino L 298n
₫ 46.400
Sản phẩm Mô Đun Điều Khiển Động Cơ Bước 8051 Arduino L 298n đang được mở bán với mức giá siêu tốt khi mua online, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Main control chip: l298n logic voltage: 5v logic current: 0ma~36ma drive voltage: 5v~35v single bridge maximum current: 2a maximum power: 25w product characteristics: this module uses st's l298n as its main drive chip.
When using a voltage greater than 12v drive, use the external 5v logic to supply electricity.
This module can improve reliability by using large capacity filter capacitance and continuous flow protection diode..
Driving module application range: l298n is a high voltage produced by st, large current motor drive chip.
The main characteristics are: High working voltage, up to 46v
High output current, peak current can reach 3a in a moment, and current is 2a in continuous operation
Rated power 25w.
A full bridge drive with two h @ - @ bridges with high voltage and high current, which can be used to drive dc motor and stepper motor, inductive load such as relay coil
Use of standard logic level signal control
Having two enabling controls, allowing or prohibiting devices from working without input signals, there is a logical power input side that makes the internal logic circuit part work at low voltage
The resistance can be detected externally and the amount of change can be fed back to the control circuit.
Use l298n chip to drive motor, which can drive either a two @ - @ phase stepper motor or a four @ - @ phase stepper motor, or two dc motor.
Instructions/caveats: this module integrates a built @ - @ in 5v power supply.
When your drive voltage is 7v @ - @ 35v, you can supply the 5v logic on the board, and when you use the 5v on the board, the+5v power supply don't enter voltage, but can lead to 5v voltage for external use when ena enables in1 in2 control out1 out2 when ember enables in3 in4 control out3
When using a voltage greater than 12v drive, use the external 5v logic to supply electricity.
This module can improve reliability by using large capacity filter capacitance and continuous flow protection diode..
Driving module application range: l298n is a high voltage produced by st, large current motor drive chip.
The main characteristics are: High working voltage, up to 46v
High output current, peak current can reach 3a in a moment, and current is 2a in continuous operation
Rated power 25w.
A full bridge drive with two h @ - @ bridges with high voltage and high current, which can be used to drive dc motor and stepper motor, inductive load such as relay coil
Use of standard logic level signal control
Having two enabling controls, allowing or prohibiting devices from working without input signals, there is a logical power input side that makes the internal logic circuit part work at low voltage
The resistance can be detected externally and the amount of change can be fed back to the control circuit.
Use l298n chip to drive motor, which can drive either a two @ - @ phase stepper motor or a four @ - @ phase stepper motor, or two dc motor.
Instructions/caveats: this module integrates a built @ - @ in 5v power supply.
When your drive voltage is 7v @ - @ 35v, you can supply the 5v logic on the board, and when you use the 5v on the board, the+5v power supply don't enter voltage, but can lead to 5v voltage for external use when ena enables in1 in2 control out1 out2 when ember enables in3 in4 control out3
Sản Phẩm Liên Quan
HOT
Bikini hàng Âu
₫ 400.000
HOT
Bikini Thái quả ngang chấm bi
₫ 350.000
HOT
Bikini made in Thailand
₫ 350.000
HOT
Bikini Thái
₫ 300.000
HOT
Bikini OKISS- QCXK
₫ 400.000
HOT
Bikini xuất Âu
₫ 300.000