Mạch Điều Khiển Bay Stm32 Cho Drone F4 F4 Pdb
790.000
₫ 553.000
Sản phẩm Mạch Điều Khiển Bay Stm32 Cho Drone F4 F4 Pdb đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 790.000 xuống còn ₫ 553.000, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Description:
English name: F4 flight control Betaflight F4 PDB STM32 integrated OSD flight controller DSHOT
Product description: This is a flight controller for mainstream FPV small racks using STM32F405 and mpu6000.
Input voltage is 2S-6S
BEC:5V
Output 3A current.
Applicable: It supports the mainstream PPM, SBUS, IBUS, DSM2/DSMX and other receptions on the market. machine.
There are LED_STRIP interface, active buzzer interface. Integrated OSD function, support OSD parameter adjustment, support the latest DSHOT ESC.
Hardware Configuration:
Main control: STM32F405RGT6
Sensor: mpu6000
Receiver: Support PPM, SBUS, IBUS, DSM2/DSMX, etc.
LED_STRIP interface
Active buzzer interface
No black box
Built-in ammeter, current detection
OSD interface
Comes with BEC 5V 3A
Dimensions 42*36MM (including the pad length of the bonding wire)
Screw hole spacing 30.5*30.5MM
Diameter 4.1MM
Weight 9.4g
The new F4 flight control:
1. Use OMNIBUSF4 firmware
2. The main control is STM32F405 GRT6, the refresh rate is up to 8K.
3.PCB 3OZ copper thickness to enhance current stability and fast heat dissipation
4. BEC is 5V3A output
5
ESC M1-M4: Connect the power cord of the ESC
V+-V-: Corresponding to the positive and negative poles of the power cord of the ESC, with a ‘-’ sign as the ground wire.
B+--B-: lithium battery input
BOOT: BOOT button (used to flash firmware)
+5V: With 3A output, it can be connected to the image transmission, receiver, and camera at the same time.
GND: Ground wire
Vout: Video output, connected to video transmission image signal line
Vin: Video input, connected to the camera signal line
LED: Programmable LED_Strip signal line output port
RX6(S): Connect SBUS receiver here
RX1(D): Connect DSM2/DSMX/IBUS receiver here
PPM: Connect the PPM receiver here
VBAT: The positive pole of the wide voltage graph transmission power supply (synchronized with the battery voltage), where the voltage is the power voltage
BUZ+, BUZ-: BB ring connection (only supports active buzzer, distinguish between positive and negative)
RX3, TX3: serial port URAT3
Packing list:
F4 flight control*1 pc
shock-absorbing ball*4pcs
Note:
1.Please allow 0-1cm error due to manual measurement. Please make sure you do not mind before you bid.
2.Due to the difference between different monitors, the picture may not reflect the actual color of the
English name: F4 flight control Betaflight F4 PDB STM32 integrated OSD flight controller DSHOT
Product description: This is a flight controller for mainstream FPV small racks using STM32F405 and mpu6000.
Input voltage is 2S-6S
BEC:5V
Output 3A current.
Applicable: It supports the mainstream PPM, SBUS, IBUS, DSM2/DSMX and other receptions on the market. machine.
There are LED_STRIP interface, active buzzer interface. Integrated OSD function, support OSD parameter adjustment, support the latest DSHOT ESC.
Hardware Configuration:
Main control: STM32F405RGT6
Sensor: mpu6000
Receiver: Support PPM, SBUS, IBUS, DSM2/DSMX, etc.
LED_STRIP interface
Active buzzer interface
No black box
Built-in ammeter, current detection
OSD interface
Comes with BEC 5V 3A
Dimensions 42*36MM (including the pad length of the bonding wire)
Screw hole spacing 30.5*30.5MM
Diameter 4.1MM
Weight 9.4g
The new F4 flight control:
1. Use OMNIBUSF4 firmware
2. The main control is STM32F405 GRT6, the refresh rate is up to 8K.
3.PCB 3OZ copper thickness to enhance current stability and fast heat dissipation
4. BEC is 5V3A output
5
ESC M1-M4: Connect the power cord of the ESC
V+-V-: Corresponding to the positive and negative poles of the power cord of the ESC, with a ‘-’ sign as the ground wire.
B+--B-: lithium battery input
BOOT: BOOT button (used to flash firmware)
+5V: With 3A output, it can be connected to the image transmission, receiver, and camera at the same time.
GND: Ground wire
Vout: Video output, connected to video transmission image signal line
Vin: Video input, connected to the camera signal line
LED: Programmable LED_Strip signal line output port
RX6(S): Connect SBUS receiver here
RX1(D): Connect DSM2/DSMX/IBUS receiver here
PPM: Connect the PPM receiver here
VBAT: The positive pole of the wide voltage graph transmission power supply (synchronized with the battery voltage), where the voltage is the power voltage
BUZ+, BUZ-: BB ring connection (only supports active buzzer, distinguish between positive and negative)
RX3, TX3: serial port URAT3
Packing list:
F4 flight control*1 pc
shock-absorbing ball*4pcs
Note:
1.Please allow 0-1cm error due to manual measurement. Please make sure you do not mind before you bid.
2.Due to the difference between different monitors, the picture may not reflect the actual color of the