LV8729 động cơ bước Driver 4 lớp chất nền cực êm lái xe LV8729 hỗ trợ lái xe 6V-36V full microstep lái xe controll
124.200
₫ 62.100
Sản phẩm LV8729 động cơ bước Driver 4 lớp chất nền cực êm lái xe LV8729 hỗ trợ lái xe 6V-36V full microstep lái xe controll đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 124.200 xuống còn ₫ 62.100, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Welcome to our shop 👑Kingzizi👑, all the products in this shop are at a favorable price💕, and have quality assurance💕, you can rest assured to buy💕, we will give you the best and highest quality shopping experience! 🌹🌹🌹
LV8729 Stepper Motor Driver With Heat Sink Replace A4988 DRV8825 Compatible With MKS Gen V1.4 Ramps 1.6 1.4 1.5 3D Printer Parts
LV8729 driver module with 128 subdivisions is a good choice for Nema stepper motor whose current is less than 1.5A, which makes motor steady, quiet and precise.
Specifications:
Dimensions: 1.5mm * 2.0mm (Same with the A4988 and DRV8825)
Maximum drive current: 1.8A (Default 0.8A)
Operating voltage: 6V-36V, the proposed voltage is 12V
Support subdivisions: 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128
Product Process: four layer PCB board
In the 64 subdivision or 128 subdivision controller it has a better ultra-quiet effect.
Note: Please make sure the connecting direction is right, or it will probably burn the driver chip and controller board. Recommend to do a good job of cooling for the module.
Driver current algorithm and its adjustment:
1. Driver current formula: I= Vref/(Rs*5), Rs=0.22Ohm, Imax=1.8A
2. Please DO NOT connect the motors when measuring the voltage, or it’s easy to burn the drive.
3. Please connect both the power supply and the USB for power when measuring the voltage.
4. Minor adjustment for potentiometer driver. Adjust it again after measurement to avoid burning driver by excessive current.
5. To increase the current by rotating the potentiometer clockwise slowly, and anticlockwise to reduce.
LV8729 Increases Heat Dissipation Tips:
To consider heat, LV8729 uses four layers of PCB to dissipate heat,meanwhile, the chip is attached with heatsink, which is default 1A.SinceLV8729 motor drive subdivision is relatively large, in order to the stable operation of the 3D printer,any stepper motor is to actively dissipate heat, for example, using fan, hanging heat sink,or installing a large fan for your cotroller board.
Package Included:
1pcs x LV8729 Stepper Motor Driver With Heat Sink
Before purchase:
1. All the goods are in stock and we will dispatch immediately if we receive the order.
2.Please read the item description, if you have any question, do not hesitate to contact us.
3.Use the vouchers for more saving.
Shipment:
1.1-2 days to ship(except for the pro-order item)
After purchase:
1.If you are satisfied,please give us 5 stars praise.
2.Please contact us before you are going to give us bad review. We are helpful and will solve the problems.
if you receive a defect item,please contact us at once with item picture or video
#LV8729 #Stepper #Motor #Driver #With #Heat #Sink #Replace #A4988 #DRV8825 #Compatible #With #MKS #Gen #V1.4 #Ramps #1.6 #1.4 #1.5 #3D #Printer
LV8729 Stepper Motor Driver With Heat Sink Replace A4988 DRV8825 Compatible With MKS Gen V1.4 Ramps 1.6 1.4 1.5 3D Printer Parts
LV8729 driver module with 128 subdivisions is a good choice for Nema stepper motor whose current is less than 1.5A, which makes motor steady, quiet and precise.
Specifications:
Dimensions: 1.5mm * 2.0mm (Same with the A4988 and DRV8825)
Maximum drive current: 1.8A (Default 0.8A)
Operating voltage: 6V-36V, the proposed voltage is 12V
Support subdivisions: 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64, 1/128
Product Process: four layer PCB board
In the 64 subdivision or 128 subdivision controller it has a better ultra-quiet effect.
Note: Please make sure the connecting direction is right, or it will probably burn the driver chip and controller board. Recommend to do a good job of cooling for the module.
Driver current algorithm and its adjustment:
1. Driver current formula: I= Vref/(Rs*5), Rs=0.22Ohm, Imax=1.8A
2. Please DO NOT connect the motors when measuring the voltage, or it’s easy to burn the drive.
3. Please connect both the power supply and the USB for power when measuring the voltage.
4. Minor adjustment for potentiometer driver. Adjust it again after measurement to avoid burning driver by excessive current.
5. To increase the current by rotating the potentiometer clockwise slowly, and anticlockwise to reduce.
LV8729 Increases Heat Dissipation Tips:
To consider heat, LV8729 uses four layers of PCB to dissipate heat,meanwhile, the chip is attached with heatsink, which is default 1A.SinceLV8729 motor drive subdivision is relatively large, in order to the stable operation of the 3D printer,any stepper motor is to actively dissipate heat, for example, using fan, hanging heat sink,or installing a large fan for your cotroller board.
Package Included:
1pcs x LV8729 Stepper Motor Driver With Heat Sink
Before purchase:
1. All the goods are in stock and we will dispatch immediately if we receive the order.
2.Please read the item description, if you have any question, do not hesitate to contact us.
3.Use the vouchers for more saving.
Shipment:
1.1-2 days to ship(except for the pro-order item)
After purchase:
1.If you are satisfied,please give us 5 stars praise.
2.Please contact us before you are going to give us bad review. We are helpful and will solve the problems.
if you receive a defect item,please contact us at once with item picture or video
#LV8729 #Stepper #Motor #Driver #With #Heat #Sink #Replace #A4988 #DRV8825 #Compatible #With #MKS #Gen #V1.4 #Ramps #1.6 #1.4 #1.5 #3D #Printer