Linh Kiện Bảng Mạch Điện Tử Arduino Esp32
381.800
₫ 191.900
Sản phẩm Linh Kiện Bảng Mạch Điện Tử Arduino Esp32 đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 381.800 xuống còn ₫ 191.900, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Descriptions:
The module is a portable power bank that supports two voltage outputs of 3V/1A and 5V/2.2A. The rated current of 5V voltage
output is 2.2A, and the maximum support current is 3A (not recommended for overload, easy to damage the module,
and accelerate the service life). The output of the current depends on the quality of the battery.
Micro USB has a charging current of 600mA-800mA and supports up to two batteries. It is recommended to use two batteries,
which can be longer.
When the switch is turned to NOMAL, the current output is lower than 30ma, and it will automatically stop in about 10 seconds
and switch to standby mode.
When it is toggled to HOLD, no matter what happens, it will remain on until the battery is dead (the 2512 resistor on the back will heat up).
Special Attention: The battery must be installed with positive and negative poles. The positive and negative poles are clearly marked
on the board, and incorrect installation will burn the module.
Specifications:
Material: PCB
Color: as shown
Size: about 110x49x16mm (LxWxH)
Compatibility: for Arduino ESP32 ESP8266
Package Included:
1pc x battery expansion board
Note:
-Due to the light difference, the item's color may be slightly different from the pictures.
-Please allow 0.5-2 cm differences due to manual measure
The module is a portable power bank that supports two voltage outputs of 3V/1A and 5V/2.2A. The rated current of 5V voltage
output is 2.2A, and the maximum support current is 3A (not recommended for overload, easy to damage the module,
and accelerate the service life). The output of the current depends on the quality of the battery.
Micro USB has a charging current of 600mA-800mA and supports up to two batteries. It is recommended to use two batteries,
which can be longer.
When the switch is turned to NOMAL, the current output is lower than 30ma, and it will automatically stop in about 10 seconds
and switch to standby mode.
When it is toggled to HOLD, no matter what happens, it will remain on until the battery is dead (the 2512 resistor on the back will heat up).
Special Attention: The battery must be installed with positive and negative poles. The positive and negative poles are clearly marked
on the board, and incorrect installation will burn the module.
Specifications:
Material: PCB
Color: as shown
Size: about 110x49x16mm (LxWxH)
Compatibility: for Arduino ESP32 ESP8266
Package Included:
1pc x battery expansion board
Note:
-Due to the light difference, the item's color may be slightly different from the pictures.
-Please allow 0.5-2 cm differences due to manual measure
Sản Phẩm Liên Quan
HOT
Bikini hàng Âu
₫ 400.000
HOT
Bikini Thái quả ngang chấm bi
₫ 350.000
HOT
Bikini made in Thailand
₫ 350.000
HOT
Bikini Thái
₫ 300.000
HOT
Bikini OKISS- QCXK
₫ 400.000
HOT
Bikini xuất Âu
₫ 300.000