ExhG❤❤❤High quality New CNC Shield V3 Engraving Machine / 3D Printer / + 4 Pcs A4988 Driver Expansion Board for Arduino
201.370
₫ 133.000
Sản phẩm ExhG❤❤❤High quality New CNC Shield V3 Engraving Machine / 3D Printer / + 4 Pcs A4988 Driver Expansion Board for Arduino đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 201.370 xuống còn ₫ 133.000, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Do you want to enjoy high-quality experience? Then get into our store and pick it up.！
Decription:
Features:
Use removable A4988 or DRV8825 compatible stepping driver.
The extension board can be used for engraving machine or 3D printer driver.
Compatible with GRBL 0.8. Open-source firmware operated on Arduino UNO, converting G code command into stepping signal.
PWM spindle and direction pin, 4 shaft support (X, Y, Z, A - you can copy X, Y, Z or use pin D12 and D13 customize firmware perform complete shaft 4).
Compact design, stepping motor can connect 4 pin connectors or be soldered.
This is a set of disassembled part, and you need basic soldering skills to solder them together.
CNC Expansion Board:
Version: V3.0
Green
68 x 53 x 18mm / 2.67 x 2.08 x 0.7"
Voltage: DC 12V to 36V (only DRV8825 driver can handle up to 36V, so please consider voltage for power supply)
4pcs A4988 Driver:
20 x 15mm / 0.78 x 0.59"
Thermal Shutdown Circuit: Yes
Cross Current Protection: Yes
Ground Fault Protection: Yes
Short Circuit Protection: Yes
Compatible Logic Voltage: 3.3V and 5V
Five Step Modes: Full, 1/2, 1/4, 1/8 and 1/16
Mix with slow current attenuation model.
Internal UVLO and low RDS (on) output.
Automatic current attenuation mode Detection/Select.
Phase-in rectifier, low power consumption.
Warning: Connecting or disconnecting stepping motor while driver is powered on might damage driver.
4pcs Heat Sinks:
8 x 8mm / 0.31 x 0.31"
Included:
1 x cnc shield v3
4 x A4988
4 x Hea
Decription:
Features:
Use removable A4988 or DRV8825 compatible stepping driver.
The extension board can be used for engraving machine or 3D printer driver.
Compatible with GRBL 0.8. Open-source firmware operated on Arduino UNO, converting G code command into stepping signal.
PWM spindle and direction pin, 4 shaft support (X, Y, Z, A - you can copy X, Y, Z or use pin D12 and D13 customize firmware perform complete shaft 4).
Compact design, stepping motor can connect 4 pin connectors or be soldered.
This is a set of disassembled part, and you need basic soldering skills to solder them together.
CNC Expansion Board:
Version: V3.0
Green
68 x 53 x 18mm / 2.67 x 2.08 x 0.7"
Voltage: DC 12V to 36V (only DRV8825 driver can handle up to 36V, so please consider voltage for power supply)
4pcs A4988 Driver:
20 x 15mm / 0.78 x 0.59"
Thermal Shutdown Circuit: Yes
Cross Current Protection: Yes
Ground Fault Protection: Yes
Short Circuit Protection: Yes
Compatible Logic Voltage: 3.3V and 5V
Five Step Modes: Full, 1/2, 1/4, 1/8 and 1/16
Mix with slow current attenuation model.
Internal UVLO and low RDS (on) output.
Automatic current attenuation mode Detection/Select.
Phase-in rectifier, low power consumption.
Warning: Connecting or disconnecting stepping motor while driver is powered on might damage driver.
4pcs Heat Sinks:
8 x 8mm / 0.31 x 0.31"
Included:
1 x cnc shield v3
4 x A4988
4 x Hea