(Mua-Code) Phụ Kiện Cho Máy In 3d For Cr-10 / Ender 3 Pin 27 Board
41.200
₫ 26.700
Sản phẩm (Mua-Code) Phụ Kiện Cho Máy In 3d For Cr-10 / Ender 3 Pin 27 Board đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 41.200 xuống còn ₫ 26.700, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Features:
1. Use this adapter, no need of cutting the wires!
2. Simply connect between the board and the cable, connect 3 for bltouch wires and upgrade the firmware.
3. Improve design with wider power channels
4. Easy and convenient to use, easy to operate
5. The motherboard is safe and stable, and the line is clear.
Specification:
Name: for Ender-3/CR-10 BL-TOUCH Adapter Plate
Applicable to for Ender-3/cr-10 to BL TOUCH
Compatible: for Ender3/Ender 3 Pro/Ender5/CR-10 Mini/CR-10
Not compatible with: for ANET A8/Ender2/Ender4/CR-8
Color: green
Packing list:
1*Adapter plate
Note:
The pin 27 plate makes it quick and easy to install a bltouch or filament sensor.
Usually you need to cut the ribbon cable and solder it to pin 27,
But the board should be able to plug and unplug. (after firmware update)
Be sure to check the wire configuration on the bltouch or filament sensor.
The new bltouch sensor should be plugged directly into the board without disengaging the connector.
From left to right: brown ground, red -5v, yellow / orange signal
Disconnect the LCD ribbon ext1 on the control board
Connect Ext1 to pin 27 board
Connect bltouch to the 3 pins on the pin 27 board. From left to right: brown ground, red -5v, yellow signal
Connect pin 27 to the motherboard. Be sure to align the plug pins on plug 27 with the motherb
1. Use this adapter, no need of cutting the wires!
2. Simply connect between the board and the cable, connect 3 for bltouch wires and upgrade the firmware.
3. Improve design with wider power channels
4. Easy and convenient to use, easy to operate
5. The motherboard is safe and stable, and the line is clear.
Specification:
Name: for Ender-3/CR-10 BL-TOUCH Adapter Plate
Applicable to for Ender-3/cr-10 to BL TOUCH
Compatible: for Ender3/Ender 3 Pro/Ender5/CR-10 Mini/CR-10
Not compatible with: for ANET A8/Ender2/Ender4/CR-8
Color: green
Packing list:
1*Adapter plate
Note:
The pin 27 plate makes it quick and easy to install a bltouch or filament sensor.
Usually you need to cut the ribbon cable and solder it to pin 27,
But the board should be able to plug and unplug. (after firmware update)
Be sure to check the wire configuration on the bltouch or filament sensor.
The new bltouch sensor should be plugged directly into the board without disengaging the connector.
From left to right: brown ground, red -5v, yellow / orange signal
Disconnect the LCD ribbon ext1 on the control board
Connect Ext1 to pin 27 board
Connect bltouch to the 3 pins on the pin 27 board. From left to right: brown ground, red -5v, yellow signal
Connect pin 27 to the motherboard. Be sure to align the plug pins on plug 27 with the motherb