Board Nguồn Đa Năng 5 Dây 5V/24V ( độ lại board nguồn tivi LCD/LED )
₫ 45.000
Sản phẩm Board Nguồn Đa Năng 5 Dây 5V/24V ( độ lại board nguồn tivi LCD/LED ) đang được mở bán với mức giá siêu tốt khi mua online, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
#ICNGUỒN
#NGUỒNĐANĂNG
-----------------------------------
Board nguồn đa năng 5 Dây: Chức năng độ lại board nguồn TIVI LCD/LED do hỏng IC nguồn,...
Độ được cho TIVI đến 55 inch
---------------------------------------------------------------
Secondary power supply: 3.3V, 5V
GACUN KLY-LCDMK-5Z series (shared within 36W)
This series of modules is designed to repair the secondary power supply damage repair of LCD LCD TVs and monitors. The maximum power can be up to 36W . It is easy for all colleagues to repair the LCD power supply. This series has small size , simple installation and basic implementation. Fully intelligent, high added value and other advantages, is a major change in the maintenance of LCD LCD TV power supply in the maintenance market , welcome to use!
* Installation instructions :
(1) First detecting Good + 300V DC voltage is the normal , and then confirm the switching transformer and the secondary peripheral parts is normal , and then confirmed when the load short-circuit failure does not re-enter the following operation. .
(2) First remove the MOS tube or thick film IC on the original machine , and fasten the module to the heat sink , then fix it on the heat sink with a screw lock (the lock screw can't be pressed too tightly, otherwise the module will be damaged) .
(3) According to the figure, the fork is disconnected in the actual circuit , and the color lines of the module are connected according to the figure. It must not be connected incorrectly. After repeated verification, the switch will not be connected, and the machine can be turned on and cut. ! Module leads cannot be extended under unnecessary conditions . Otherwise it will affect normal operation .
* Description of each lead connection:
1. Red line: Connect the main voltage +300V through the switching voltage device (ie D- pole of MOS tube , thick film IC D pole) .
2, black line : connected to the negative pole , that is , the power tube is hot .
3, blue line : connect the original machine main voltage (3.3V or 5V) voltage regulator optocoupler 4 feet (some original multi-optocoupler in parallel according to the original machine connection), 3 feet grounding.
4, white line :. Connect the original machine switch transformer feedback coil rectifier diode (pictured).
5, green line : the original machine main voltage
#NGUỒNĐANĂNG
-----------------------------------
Board nguồn đa năng 5 Dây: Chức năng độ lại board nguồn TIVI LCD/LED do hỏng IC nguồn,...
Độ được cho TIVI đến 55 inch
---------------------------------------------------------------
Secondary power supply: 3.3V, 5V
GACUN KLY-LCDMK-5Z series (shared within 36W)
This series of modules is designed to repair the secondary power supply damage repair of LCD LCD TVs and monitors. The maximum power can be up to 36W . It is easy for all colleagues to repair the LCD power supply. This series has small size , simple installation and basic implementation. Fully intelligent, high added value and other advantages, is a major change in the maintenance of LCD LCD TV power supply in the maintenance market , welcome to use!
* Installation instructions :
(1) First detecting Good + 300V DC voltage is the normal , and then confirm the switching transformer and the secondary peripheral parts is normal , and then confirmed when the load short-circuit failure does not re-enter the following operation. .
(2) First remove the MOS tube or thick film IC on the original machine , and fasten the module to the heat sink , then fix it on the heat sink with a screw lock (the lock screw can't be pressed too tightly, otherwise the module will be damaged) .
(3) According to the figure, the fork is disconnected in the actual circuit , and the color lines of the module are connected according to the figure. It must not be connected incorrectly. After repeated verification, the switch will not be connected, and the machine can be turned on and cut. ! Module leads cannot be extended under unnecessary conditions . Otherwise it will affect normal operation .
* Description of each lead connection:
1. Red line: Connect the main voltage +300V through the switching voltage device (ie D- pole of MOS tube , thick film IC D pole) .
2, black line : connected to the negative pole , that is , the power tube is hot .
3, blue line : connect the original machine main voltage (3.3V or 5V) voltage regulator optocoupler 4 feet (some original multi-optocoupler in parallel according to the original machine connection), 3 feet grounding.
4, white line :. Connect the original machine switch transformer feedback coil rectifier diode (pictured).
5, green line : the original machine main voltage
Sản Phẩm Liên Quan
HOT
HOT