Board Cao Áp Led Đa Năng Cho TV LED 26 - 65 Inch
₫ 100.000
Sản phẩm Board Cao Áp Led Đa Năng Cho TV LED 26 - 65 Inch đang được mở bán với mức giá siêu tốt khi mua online, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,2 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Board cao áp đa năng Led LCD TV
Chức năng: độ lại mạch cao áp bị hỏng trên LCD TV Led
Điện áp đầu vào: 10v -28v
Độ được cho LCD TV Led 26 - 65 inch
-----------------------------------------------------------------------
[Power supply operating conditions] Input: Support 10-28V DC input
[Output voltage] Automatic adaptation below 88V (the lowest limit is the input voltage value, no buck)
[Output current] default 80mA, by shorting R22 R21 R18 R15 R24 resistor, you can increase the current, each resistor 80mA. Up to 480mA.
[Applicable light bar] Large size 26 inch - 65 inch (maximum voltage 88V)
[Input interface definition]
1: Power supply
2: Power supply
3: ENA switch control
4: Brightness adjustment signal (voltage dimming)
5: Ground line
6: Ground line
[Output interface definition]: Positive and negative (++--) has four parallel interfaces, the definition is the same.
[Important features]:
1: With protection.
2: The output voltage is below 88V automatically.
3: It is convenient to change the current. There are 6 1206 resistors on the motherboard, one resistor represents 80mA, and the highest 6 resistors are connected to 480mA.
4: By default, only one R13 resistor is connected, and the output current is 80mA, which will not burn the light bar. If it is too dark, flickering or flashing off, try increasing the current. Until the brightness is normal, the light bar will not be hot.
5: The board will not burn if it is not connected to the load (the output voltage will drop to the input voltage when the load or the light bar is broken, or will decrease to the input voltage when the load voltage is higher than 88V).
6: With 4 output interfaces, the universal definition ++--, when connecting the 2pin left and right negative light bar interface, directly insert the middle 2, 3 pins, 1 and 4 pins are e
Chức năng: độ lại mạch cao áp bị hỏng trên LCD TV Led
Điện áp đầu vào: 10v -28v
Độ được cho LCD TV Led 26 - 65 inch
-----------------------------------------------------------------------
[Power supply operating conditions] Input: Support 10-28V DC input
[Output voltage] Automatic adaptation below 88V (the lowest limit is the input voltage value, no buck)
[Output current] default 80mA, by shorting R22 R21 R18 R15 R24 resistor, you can increase the current, each resistor 80mA. Up to 480mA.
[Applicable light bar] Large size 26 inch - 65 inch (maximum voltage 88V)
[Input interface definition]
1: Power supply
2: Power supply
3: ENA switch control
4: Brightness adjustment signal (voltage dimming)
5: Ground line
6: Ground line
[Output interface definition]: Positive and negative (++--) has four parallel interfaces, the definition is the same.
[Important features]:
1: With protection.
2: The output voltage is below 88V automatically.
3: It is convenient to change the current. There are 6 1206 resistors on the motherboard, one resistor represents 80mA, and the highest 6 resistors are connected to 480mA.
4: By default, only one R13 resistor is connected, and the output current is 80mA, which will not burn the light bar. If it is too dark, flickering or flashing off, try increasing the current. Until the brightness is normal, the light bar will not be hot.
5: The board will not burn if it is not connected to the load (the output voltage will drop to the input voltage when the load or the light bar is broken, or will decrease to the input voltage when the load voltage is higher than 88V).
6: With 4 output interfaces, the universal definition ++--, when connecting the 2pin left and right negative light bar interface, directly insert the middle 2, 3 pins, 1 and 4 pins are e