Bộ 3 Linh Kiện Bán Dẫn Ews Immo Emultor Cho Bmw Ews2 Ews3.2 Ews 2 3.2 E38 E39
758.300
₫ 452.100
Sản phẩm Bộ 3 Linh Kiện Bán Dẫn Ews Immo Emultor Cho Bmw Ews2 Ews3.2 Ews 2 3.2 E38 E39 đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 758.300 xuống còn ₫ 452.100, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Description:
This device can emulate BMW EWS 2 and EWS 3.2 immobilizer (EWS module) in cases when old system restore is impossible .
In case of EWS3.2 similar procedure is used, only difference is that that it is NOT connected directly to diagnostic K-line.
There are NO any counters or car starts limited. You can change and store new ISN without any limitations.
Specification:
INSTALLATION:
-Remove old EWS2 control unit, find +12v ACC, GND, K-line wires, attach emulator. Emulator must be in service mode: JUMPER 1 shorted.
-Connect ANY K-line diagnostic adapter to vehicle diagnostic connector and launch EMULATOR CONFIGURATION UTILITY:
-Choose COM port, write in desired ISN number, press button Store. Or -
-For some ECU s it is possible to read ISN number directly from engine control unit. In this case select option ''ECU xxxxx'', press Read. Software will try to read ISN. If successful,
chooseoption ''EWS emulator'' and press button Store to save ISN number into emulator.
-Disconnect emulator from K-line, remove JUMPER 1 and connect K output from emulator to
DME(DDE) EWS line.
-Don't forget to short two starter relay wires (EWS connector)!
-Car is ready to start.
Package Includes:
3 Pieces Emul
This device can emulate BMW EWS 2 and EWS 3.2 immobilizer (EWS module) in cases when old system restore is impossible .
In case of EWS3.2 similar procedure is used, only difference is that that it is NOT connected directly to diagnostic K-line.
There are NO any counters or car starts limited. You can change and store new ISN without any limitations.
Specification:
INSTALLATION:
-Remove old EWS2 control unit, find +12v ACC, GND, K-line wires, attach emulator. Emulator must be in service mode: JUMPER 1 shorted.
-Connect ANY K-line diagnostic adapter to vehicle diagnostic connector and launch EMULATOR CONFIGURATION UTILITY:
-Choose COM port, write in desired ISN number, press button Store. Or -
-For some ECU s it is possible to read ISN number directly from engine control unit. In this case select option ''ECU xxxxx'', press Read. Software will try to read ISN. If successful,
chooseoption ''EWS emulator'' and press button Store to save ISN number into emulator.
-Disconnect emulator from K-line, remove JUMPER 1 and connect K output from emulator to
DME(DDE) EWS line.
-Don't forget to short two starter relay wires (EWS connector)!
-Car is ready to start.
Package Includes:
3 Pieces Emul
Sản Phẩm Liên Quan
HOT
Bikini hàng Âu
₫ 400.000
HOT
Bikini Thái quả ngang chấm bi
₫ 350.000
HOT
Bikini made in Thailand
₫ 350.000
HOT
Bikini Thái
₫ 300.000
HOT
Bikini OKISS- QCXK
₫ 400.000
HOT
Bikini xuất Âu
₫ 300.000