Bảng Mạch Phát Triển Lora Esp32 0.96 Inch Blue Oled Sx1278 Bluetooth Wifi Lora Kit 32 Arduino
838.383
₫ 595.000
Sản phẩm Bảng Mạch Phát Triển Lora Esp32 0.96 Inch Blue Oled Sx1278 Bluetooth Wifi Lora Kit 32 Arduino đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 838.383 xuống còn ₫ 595.000, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
If you need the information of this product,please contact us.
WIFI Kit series is the new development of the cost-effective networking program, the main chip using ESP32, LX6 dual-core processor, clocked at 240MHz, computing power up to 600DMIPS, chip built-in 520 KB SRAM, 802.11 b / g / N HT40 Wi-Fi transceiver, baseband, protocol stack and LWIP, integrated dual-mode Bluetooth (traditional Bluetooth and BLE low power Bluetooth).
This product is based on the WIFI Kit 32 added SX1278 chip, that is, LoRa ™ remote modem, 433MHz frequency, about -148dBm high sensitivity, +20 dBm power output, high reliability, transmission distance (measured open area communication distance 2.6Km).
Onboard 32MByte Flash, Wi-Fi antenna, 0.96-inch blue OLED display, lithium battery charging circuit and interface, CP2102 USB to serial chip, the perfect support for Arduino development environment, can be very simple and fast for program verification and product development.
Frequency: 433MHz
Operating voltage: 3.3V to 7V.
Operating temperature range: -40 ° C to + 90 ° C.
Supports Sniffer, Station, softAP and Wi-Fi Direct modes.
Transmit power: 19.5 dBm @ 11b, 16.5 dBm @ 11g, 15.5 dBm @ 11n.
Data rate: 150 Mbps @ 11n HT40,72 Mbps @ 11n HT20,54 Mbps @ 11g, 11 Mbps @ 11b.
Receiver sensitivity up to - 139 dBm.
UDP continues to throughput by 135 Mbps.
The LoRa communication function of WIFlLoRa 32 must be used with an antenna with the same frequency. If there is no antenna, the LoRa chip may be damaged. The onboard lithium battery charging and discharging circuit, the orange LED light will go out when the battery is fully charged, it only provides basic lithium battery charging and discharging functions, and cannot monitor the battery temperature and power. Please pay attention to the positive and negative poles of the battery when using the battery. Reverse connection may explode. To use the IO with touch function on the board as the touch signal input (WIFI Kit32 and LoRa 32 have this function), please add a 100nF pull-down capacitor to this
WIFI Kit series is the new development of the cost-effective networking program, the main chip using ESP32, LX6 dual-core processor, clocked at 240MHz, computing power up to 600DMIPS, chip built-in 520 KB SRAM, 802.11 b / g / N HT40 Wi-Fi transceiver, baseband, protocol stack and LWIP, integrated dual-mode Bluetooth (traditional Bluetooth and BLE low power Bluetooth).
This product is based on the WIFI Kit 32 added SX1278 chip, that is, LoRa ™ remote modem, 433MHz frequency, about -148dBm high sensitivity, +20 dBm power output, high reliability, transmission distance (measured open area communication distance 2.6Km).
Onboard 32MByte Flash, Wi-Fi antenna, 0.96-inch blue OLED display, lithium battery charging circuit and interface, CP2102 USB to serial chip, the perfect support for Arduino development environment, can be very simple and fast for program verification and product development.
Frequency: 433MHz
Operating voltage: 3.3V to 7V.
Operating temperature range: -40 ° C to + 90 ° C.
Supports Sniffer, Station, softAP and Wi-Fi Direct modes.
Transmit power: 19.5 dBm @ 11b, 16.5 dBm @ 11g, 15.5 dBm @ 11n.
Data rate: 150 Mbps @ 11n HT40,72 Mbps @ 11n HT20,54 Mbps @ 11g, 11 Mbps @ 11b.
Receiver sensitivity up to - 139 dBm.
UDP continues to throughput by 135 Mbps.
The LoRa communication function of WIFlLoRa 32 must be used with an antenna with the same frequency. If there is no antenna, the LoRa chip may be damaged. The onboard lithium battery charging and discharging circuit, the orange LED light will go out when the battery is fully charged, it only provides basic lithium battery charging and discharging functions, and cannot monitor the battery temperature and power. Please pay attention to the positive and negative poles of the battery when using the battery. Reverse connection may explode. To use the IO with touch function on the board as the touch signal input (WIFI Kit32 and LoRa 32 have this function), please add a 100nF pull-down capacitor to this
Sản Phẩm Liên Quan
HOT
Bikini hàng Âu
₫ 400.000
HOT
Bikini Thái quả ngang chấm bi
₫ 350.000
HOT
Bikini made in Thailand
₫ 350.000
HOT
Bikini Thái
₫ 300.000
HOT
Bikini OKISS- QCXK
₫ 400.000
HOT
Bikini xuất Âu
₫ 300.000