Bảng Mạch Cho Raspberry Pi 2.13 Inch 250x122 Cho Arduino G8Vn
₫ 442.000
Sản phẩm Bảng Mạch Cho Raspberry Pi 2.13 Inch 250x122 Cho Arduino G8Vn đang được mở bán với mức giá siêu tốt khi mua online, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
1. Without backlight, the last content can be displayed for a long time even if the power is off
2. Ultra-low power consumption, basically only need to refresh
3. Standard for Raspberry Pi 40PIN GPIO expansion header power supply, support Raspberry Pi series boards, Jetson Nano
4. The solder pads reserved for the SPI interface are used to connect with other controller boards such as for Arduino / Nucleo.
5. Onboard voltage converter, compatible with 3.3V / 5V MCU
specification:
Interface: SPI
Dimensions: 65mmx30.2mm
Display size: 23.71mmx48.55mm
Dot pitch: 0.194x0.194
Resolution: 250x122
Display color: black, white
Gray level: 2
Partial refresh time: 0.3s
Full refresh time: 2s
Refresh power: 26.4mW (typical value)
Standby power: less than 0.017mW
Viewing angle: more than 170 degree
GND: GND
DIN: SPI communication MOSI pin
CLK: SPI communication SCK pin
CS: SPI chip select pin (active low)
DC: data/command control pin (high level means data, low level means command)
RST: External reset pin (low level reset)
BUSY: Busy output pin (low level means busy)
colour: blue
Material: plastic
Package Contents:
1 * 2.13 inch electronic paper HAT
1 * Screw set
1 * PH2.0 20cm 8Pin
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1
2. Ultra-low power consumption, basically only need to refresh
3. Standard for Raspberry Pi 40PIN GPIO expansion header power supply, support Raspberry Pi series boards, Jetson Nano
4. The solder pads reserved for the SPI interface are used to connect with other controller boards such as for Arduino / Nucleo.
5. Onboard voltage converter, compatible with 3.3V / 5V MCU
specification:
Interface: SPI
Dimensions: 65mmx30.2mm
Display size: 23.71mmx48.55mm
Dot pitch: 0.194x0.194
Resolution: 250x122
Display color: black, white
Gray level: 2
Partial refresh time: 0.3s
Full refresh time: 2s
Refresh power: 26.4mW (typical value)
Standby power: less than 0.017mW
Viewing angle: more than 170 degree
GND: GND
DIN: SPI communication MOSI pin
CLK: SPI communication SCK pin
CS: SPI chip select pin (active low)
DC: data/command control pin (high level means data, low level means command)
RST: External reset pin (low level reset)
BUSY: Busy output pin (low level means busy)
colour: blue
Material: plastic
Package Contents:
1 * 2.13 inch electronic paper HAT
1 * Screw set
1 * PH2.0 20cm 8Pin
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1
Sản Phẩm Liên Quan
HOT