3D printer StepStick DRV8825 stepper motor driver Carrier Reprap 4 layers PCB board
₫ 43.324
Sản phẩm 3D printer StepStick DRV8825 stepper motor driver Carrier Reprap 4 layers PCB board đang được mở bán với mức giá siêu tốt khi mua online, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Introduction to the
The DRV8825 stepper motor driver carrier plate TI DRV8825 microbipolar stepper motor driver is a breakthrough. The module has a pin distribution and interface almost identical to our A4988 stepper motor driver carrier, so it can be used as a substitute for these boards in a number of applications for higher performance drop-down menus. DRV8825 with adjustable current limit, overcurrent and overheat protection, six microresolutions (down 1/32- Step). It uses 8.2-45V and can provide up to about 1.5 per phase without fins or forced air flow (rated up to 2.2 with sufficient additional cooling per volume).
Product features
1. Simple steps and direction control interface
2. Six different step resolutions: full step, half step, 1/4-step1/8-step1/16- Step, 1/32- Step
3.CAN interface directly with 3.3V and 5V systems
4. Heat off over temperature, over current off, under voltage lock
5. Short to ground short-circuit load protection
6.4 layer 2 oz copper PCB for increased heat dissipation
7. Bare welding below the driver IC's printed circuit board on the bottom of the grounding pad
8. The module size, pin and interface match the A4988 stepper motor driver operator in many ways
9. Adjustable current control allows you to set up a potentiometer that allows you to use the rated voltage of the stepping motor above the rated voltage to output maximum current at a higher stepping rate
10. Intelligent chopper control can automatically select the correct current attenuation mode (fast or slow attenuation)
11. Maximum 45 V power supply voltage
12. Built-in voltage regulator (any external logic power supply voltage is requ
The DRV8825 stepper motor driver carrier plate TI DRV8825 microbipolar stepper motor driver is a breakthrough. The module has a pin distribution and interface almost identical to our A4988 stepper motor driver carrier, so it can be used as a substitute for these boards in a number of applications for higher performance drop-down menus. DRV8825 with adjustable current limit, overcurrent and overheat protection, six microresolutions (down 1/32- Step). It uses 8.2-45V and can provide up to about 1.5 per phase without fins or forced air flow (rated up to 2.2 with sufficient additional cooling per volume).
Product features
1. Simple steps and direction control interface
2. Six different step resolutions: full step, half step, 1/4-step1/8-step1/16- Step, 1/32- Step
3.CAN interface directly with 3.3V and 5V systems
4. Heat off over temperature, over current off, under voltage lock
5. Short to ground short-circuit load protection
6.4 layer 2 oz copper PCB for increased heat dissipation
7. Bare welding below the driver IC's printed circuit board on the bottom of the grounding pad
8. The module size, pin and interface match the A4988 stepper motor driver operator in many ways
9. Adjustable current control allows you to set up a potentiometer that allows you to use the rated voltage of the stepping motor above the rated voltage to output maximum current at a higher stepping rate
10. Intelligent chopper control can automatically select the correct current attenuation mode (fast or slow attenuation)
11. Maximum 45 V power supply voltage
12. Built-in voltage regulator (any external logic power supply voltage is requ
Sản Phẩm Liên Quan
HOT
Bikini hàng Âu
₫ 400.000
HOT
Bikini Thái quả ngang chấm bi
₫ 350.000
HOT
Bikini made in Thailand
₫ 350.000
HOT
Bikini Thái
₫ 300.000
HOT
Bikini OKISS- QCXK
₫ 400.000
HOT
Bikini xuất Âu
₫ 300.000