1 Bảng Mạch Lập Trình Avr Isp Cho Arduino Uno R3 Mega2560 Atmega328P Nano Pro
127.178
₫ 85.200
Sản phẩm 1 Bảng Mạch Lập Trình Avr Isp Cho Arduino Uno R3 Mega2560 Atmega328P Nano Pro đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 127.178 xuống còn ₫ 85.200, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
AVR ISP Shield burns the Bootloader programmer as Arduno UNO R3
description:
This is an extended shield for programmers, allowing your Arduno board to modify the fuse position and burn the bootloader to external chips and other Arduno boards.
The onboard buzzer and LED indicator indicate whether the programming is successful, which is convenient for Arduno board designers to perform batch programming. According to the OPEN-SMART user manual, it is very easy to use.
feature:
Compatibility: Because it uses the SPI pin of the ICSP interface, it is compatible with Arduno UNO R3 / Arduno Mega2560. When it is directly plugged into two boards, it can be changed to a bootloader burner.
Working voltage: 5V
Working current: 500mA (maximum)
Arduino board burning: support Arduno UNO R3 / Mega2560 / Nano / pro mini (5V 16M)
The onboard buzzer, if the fuse bit is successfully modified, it will sound once, and then if the bootloader is programmed normally, it will sound again. If it is not two beeps, programming fails. You can capture sound instead of LED lights, so this will increase the efficiency of burning.
Onboard LED indicator, HEART BEAT LED will light up like a breathing light when it is normally powered on. During programming, the PROG indicator flashes until completion. If the programming is not successful, the ERROR indicator (red) will light up.
Onboard 28P locking seat, used for Atmega328P, Atmega168P, Atmega8 boot program burning
Onboard ISP_6PIN interface, used for external Arduino board bootloader programming
Onboard ISP_10PIN interface
The onboard FT232RL and CH340G USB to TTL programmer interface are used to upload codes to the chip on the 28P lock
description:
This is an extended shield for programmers, allowing your Arduno board to modify the fuse position and burn the bootloader to external chips and other Arduno boards.
The onboard buzzer and LED indicator indicate whether the programming is successful, which is convenient for Arduno board designers to perform batch programming. According to the OPEN-SMART user manual, it is very easy to use.
feature:
Compatibility: Because it uses the SPI pin of the ICSP interface, it is compatible with Arduno UNO R3 / Arduno Mega2560. When it is directly plugged into two boards, it can be changed to a bootloader burner.
Working voltage: 5V
Working current: 500mA (maximum)
Arduino board burning: support Arduno UNO R3 / Mega2560 / Nano / pro mini (5V 16M)
The onboard buzzer, if the fuse bit is successfully modified, it will sound once, and then if the bootloader is programmed normally, it will sound again. If it is not two beeps, programming fails. You can capture sound instead of LED lights, so this will increase the efficiency of burning.
Onboard LED indicator, HEART BEAT LED will light up like a breathing light when it is normally powered on. During programming, the PROG indicator flashes until completion. If the programming is not successful, the ERROR indicator (red) will light up.
Onboard 28P locking seat, used for Atmega328P, Atmega168P, Atmega8 boot program burning
Onboard ISP_6PIN interface, used for external Arduino board bootloader programming
Onboard ISP_10PIN interface
The onboard FT232RL and CH340G USB to TTL programmer interface are used to upload codes to the chip on the 28P lock
Sản Phẩm Liên Quan
HOT
Bọt biển vệ sinh mũi mỏ hàn
₫ 2.000
HOT
Dây hơi khí nén PU bán theo mét
₫ 3.500