W5100 Ethernet Shield Lan Cable For Arduino R3
203.508
₫ 187.228
Sản phẩm W5100 Ethernet Shield Lan Cable For Arduino R3 đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 203.508 xuống còn ₫ 187.228, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Ethernet Shield W5100
Hardwired TCP/IP embedded Ethernet controller that enables easier Internet connection for embedded systems.
Key Features
Hardwired TCP/IP protocols : TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
Un-attackable hardware network engine for preventing network attacks such as flooding, spoofing, injection
Host Interface : Direct/Indirect Bus & Serial Peripheral Interface (SPI MODE 0, 3)
4 Independent hardware socket
Internal 16Kbytes memory for TCP/IP packet processing
10BaseT / 100Base TX Ethernet PHY Embedded
Support Auto-Negotiation (Full & Half Duplex, 10 & 100 Based)
Support Auto-MDIX
3.3V Operation with 5V I/O signal tolerance
LED outputs (TX, RX, full/half duplex, Collision, link, speed)
80LQFP lead-free package (10x10mm)
The shield contains a number of informational LEDs:
PWR: indicates that the board and shield are powered
LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
FULLD: indicates that the network connection is full duplex
100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
RX: flashes when the shield receives data
TX: flashes when the shield sends data
COLL: flashes when network collisions are detected
Any Question can pm us
#w5100 #ethernetshield #arduinolan #Arduino #S
Hardwired TCP/IP embedded Ethernet controller that enables easier Internet connection for embedded systems.
Key Features
Hardwired TCP/IP protocols : TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
Un-attackable hardware network engine for preventing network attacks such as flooding, spoofing, injection
Host Interface : Direct/Indirect Bus & Serial Peripheral Interface (SPI MODE 0, 3)
4 Independent hardware socket
Internal 16Kbytes memory for TCP/IP packet processing
10BaseT / 100Base TX Ethernet PHY Embedded
Support Auto-Negotiation (Full & Half Duplex, 10 & 100 Based)
Support Auto-MDIX
3.3V Operation with 5V I/O signal tolerance
LED outputs (TX, RX, full/half duplex, Collision, link, speed)
80LQFP lead-free package (10x10mm)
The shield contains a number of informational LEDs:
PWR: indicates that the board and shield are powered
LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
FULLD: indicates that the network connection is full duplex
100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
RX: flashes when the shield receives data
TX: flashes when the shield sends data
COLL: flashes when network collisions are detected
Any Question can pm us
#w5100 #ethernetshield #arduinolan #Arduino #S
Sản Phẩm Liên Quan
HOT