V3 Engraving Machine Expansion Board + A4988 Driver (Green) with Heat Sink for Arduino Cnc Diy Set
248.000
₫ 124.000
Sản phẩm V3 Engraving Machine Expansion Board + A4988 Driver (Green) with Heat Sink for Arduino Cnc Diy Set đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 248.000 xuống còn ₫ 124.000, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Latest For CNC Shield Version 3.0 for Arduino
GRBL 0.9 compatible (Open source firmware that runs on an UNO for Arduino that turns G-code commands into stepper signals)
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
A4988 Stepper Motor Driver Board is a breakout board for Allegro's A4988 DMOS Micro-stepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefully before using this product
Specifications:
CNC Shield Board:
1. PWM Spindle and direction pins
2. 2 x End stops for each axis (6 in total)
3. Coolant enable
4. Uses removable A4988 or DRV8825 compatible stepper drivers
5. Compact design
6. Stepper Motors can be connected with 4 pin molex connectors or soldered in place
7. Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
8. Please note that this is an unassembled kit and Basic soldering skills are needed
A4988 Stepper Motor Driver:
1. Low RDS (On) Output
2. Automatic current decay e detection / selection
3. Mix with slow current decay es
4. Synchronous rectification for low power dissipation
5. Internal UVLO
6. Crossover-current protection
7. 3.3 and 5 V compatible logic supply
8. Thermal shutdown circuitry
9. Ground fault protection
10. Load short-circuit protection
11. Five selectable step es: full, 1/2, 1/4, 1/8 and 1/16
12. Warning: Connecting or disconnecting a stepper motor while the driver is
powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble)
colour: as shown
Material: PCB
size: 11x6x2cm
Package Contents:
1 x Shield Board For CNC
4 x A4988 Stepper Motor Driver (Green)
4 x Mini Heat Sink
/
1 x Shield Board For CNC
4 x A4988 Stepper Motor Driver (Red)
4 x Mini HeatSink
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1
GRBL 0.9 compatible (Open source firmware that runs on an UNO for Arduino that turns G-code commands into stepper signals)
4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
A4988 Stepper Motor Driver Board is a breakout board for Allegro's A4988 DMOS Micro-stepping Driver with Translator and Overcurrent Protection; please read the A4988 datasheet carefully before using this product
Specifications:
CNC Shield Board:
1. PWM Spindle and direction pins
2. 2 x End stops for each axis (6 in total)
3. Coolant enable
4. Uses removable A4988 or DRV8825 compatible stepper drivers
5. Compact design
6. Stepper Motors can be connected with 4 pin molex connectors or soldered in place
7. Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
8. Please note that this is an unassembled kit and Basic soldering skills are needed
A4988 Stepper Motor Driver:
1. Low RDS (On) Output
2. Automatic current decay e detection / selection
3. Mix with slow current decay es
4. Synchronous rectification for low power dissipation
5. Internal UVLO
6. Crossover-current protection
7. 3.3 and 5 V compatible logic supply
8. Thermal shutdown circuitry
9. Ground fault protection
10. Load short-circuit protection
11. Five selectable step es: full, 1/2, 1/4, 1/8 and 1/16
12. Warning: Connecting or disconnecting a stepper motor while the driver is
powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble)
colour: as shown
Material: PCB
size: 11x6x2cm
Package Contents:
1 x Shield Board For CNC
4 x A4988 Stepper Motor Driver (Green)
4 x Mini Heat Sink
/
1 x Shield Board For CNC
4 x A4988 Stepper Motor Driver (Red)
4 x Mini HeatSink
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1
Sản Phẩm Liên Quan
HOT
Bikini hàng Âu
₫ 400.000
HOT
Bikini Thái quả ngang chấm bi
₫ 350.000
HOT
Bikini made in Thailand
₫ 350.000
HOT
Bikini Thái
₫ 300.000
HOT
Bikini OKISS- QCXK
₫ 400.000
HOT
Bikini xuất Âu
₫ 300.000