Mô Đun Cảm Biến Hồng Ngoại Hc-Sr501 Cho Arduino Raspberry Pi Super
₫ 20.000
Sản phẩm Mô Đun Cảm Biến Hồng Ngoại Hc-Sr501 Cho Arduino Raspberry Pi Super đang được mở bán với mức giá siêu tốt khi mua online, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Hello.this is fitowfree store,welcome!
Description:
It is great for microcontrollers such as arduino for funduino and many more including the rasberry pi!
It is a HC--SR501 Sensor Module with an operating voltage of 5v to 20v.
Operating voltage. It has a high value of 3.3 volts and a low of 0 (it is either on or off). It's delay time can be adjusted from 5 to 200seconds as well as the sensing range from 3meter to 7meters. The entire sensor with the board is 32mm by 24mm (standard pir motion sensor). The sensor either gives off a 3.3volt high value when motion is detected and then resumes or continues to give off a 0 voltage when no motion is detected. If you use an arduino or other micro controllers you can use the 3.3 volt out to power the sensor or use the 5 volt power pin (vcc) to power the sensor. Either one will work.
Specification：
Working voltage range: DC 4.8-20V
Static current: <50uA
High level output: 3.3 V / low 0V
Trigger mode: L unrepeatable trigger /H repeated trigger (Default Repeating trigger)
Delay time: 0.5-200S (adjustable) can be produced range 0.1 seconds to a few minutes.
Blocking time: 2.5S (the default) can be produced range 0.1 seconds to tens of seconds.
Size: approx. 32mm*24mm circuit board
Induction angle: <100 degree cone angle
Working temperature: -15-+70 degrees
Induction of lens size: diameter: 23mm (default)
Note:
Please be reminded that due to lighting effects and monitor's brightness/contrast settings etc, the color tone of the photo and the actual item could be slightly different.
Package Included:
1pc New HC-SR501 Infrared PIR Motion Sensor Module
Have a nice
Description:
It is great for microcontrollers such as arduino for funduino and many more including the rasberry pi!
It is a HC--SR501 Sensor Module with an operating voltage of 5v to 20v.
Operating voltage. It has a high value of 3.3 volts and a low of 0 (it is either on or off). It's delay time can be adjusted from 5 to 200seconds as well as the sensing range from 3meter to 7meters. The entire sensor with the board is 32mm by 24mm (standard pir motion sensor). The sensor either gives off a 3.3volt high value when motion is detected and then resumes or continues to give off a 0 voltage when no motion is detected. If you use an arduino or other micro controllers you can use the 3.3 volt out to power the sensor or use the 5 volt power pin (vcc) to power the sensor. Either one will work.
Specification：
Working voltage range: DC 4.8-20V
Static current: <50uA
High level output: 3.3 V / low 0V
Trigger mode: L unrepeatable trigger /H repeated trigger (Default Repeating trigger)
Delay time: 0.5-200S (adjustable) can be produced range 0.1 seconds to a few minutes.
Blocking time: 2.5S (the default) can be produced range 0.1 seconds to tens of seconds.
Size: approx. 32mm*24mm circuit board
Induction angle: <100 degree cone angle
Working temperature: -15-+70 degrees
Induction of lens size: diameter: 23mm (default)
Note:
Please be reminded that due to lighting effects and monitor's brightness/contrast settings etc, the color tone of the photo and the actual item could be slightly different.
Package Included:
1pc New HC-SR501 Infrared PIR Motion Sensor Module
Have a nice