[Mã ELFLASH5 giảm 20K đơn 50K] Mạch chuyển đổi tín hiệu dòng điện sang điện áp (4~20mA Application)
₫ 200.000
Sản phẩm [Mã ELFLASH5 giảm 20K đơn 50K] Mạch chuyển đổi tín hiệu dòng điện sang điện áp (4~20mA Application) đang được mở bán với mức giá siêu tốt khi mua online, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
INTRODUCTION
This current-to-voltage module can linearly convert 0~25mA current signals into 0~3V voltage signals. Industrial sensors or devices usually have the current signal output of 4~20 mA. With this current-to-voltage module, your main control board can easily attain the current signals input from industrial sensors or devices.
Normally, current signals lower than 4mA can be used for fault diagnosis, and current signals higher than 20mA can be used for overrun detection. Therefore, this module is specially designed with a wide detection range from 0 to 25mA, and compatible with fault detection, overrun detection applications.
This module employs 0.1% high precision sense resistor and ultra-low noise rail-to-rail zero-drift op amp, high accuracy, no need to calibration, so it is convenient to use. 3.3V~5.5V wide voltage power supply, 0~3V voltage signal output, which are compatible with more main control boards, adapt to more applications.
NOTE: For higher accuracy, it is recommended to measure with 12 or more bit ADC!
FEATURES
Support wide voltage of 3.3~5.5V
Deploy 0.1% high precision sense resistor and ultra low noise rail-to-rail zero-drift op amp, high accuracy, and no need to calibration
Wide measurement range up to 0~25mA, which is compatible with fault diagnosis, overrun detection applications
SPECIFICATION
Supply Voltage: 3.3~5.5V
Detection Range: 0~25mA DC
Measurement Accuracy: ±0.5% F.S. @ 16-bit ADC, ±2% F.S. @ 10-bit ADC
Termination Resistance: 120Ω
Connector Type: PH2.0-3P
Product Size: 30mm * 22mm (1.18inch * 0.87inch)
SHIPPING LIST
Analog Current to Voltage Converter x1
Digital Sensor Cable 3pin
This current-to-voltage module can linearly convert 0~25mA current signals into 0~3V voltage signals. Industrial sensors or devices usually have the current signal output of 4~20 mA. With this current-to-voltage module, your main control board can easily attain the current signals input from industrial sensors or devices.
Normally, current signals lower than 4mA can be used for fault diagnosis, and current signals higher than 20mA can be used for overrun detection. Therefore, this module is specially designed with a wide detection range from 0 to 25mA, and compatible with fault detection, overrun detection applications.
This module employs 0.1% high precision sense resistor and ultra-low noise rail-to-rail zero-drift op amp, high accuracy, no need to calibration, so it is convenient to use. 3.3V~5.5V wide voltage power supply, 0~3V voltage signal output, which are compatible with more main control boards, adapt to more applications.
NOTE: For higher accuracy, it is recommended to measure with 12 or more bit ADC!
FEATURES
Support wide voltage of 3.3~5.5V
Deploy 0.1% high precision sense resistor and ultra low noise rail-to-rail zero-drift op amp, high accuracy, and no need to calibration
Wide measurement range up to 0~25mA, which is compatible with fault diagnosis, overrun detection applications
SPECIFICATION
Supply Voltage: 3.3~5.5V
Detection Range: 0~25mA DC
Measurement Accuracy: ±0.5% F.S. @ 16-bit ADC, ±2% F.S. @ 10-bit ADC
Termination Resistance: 120Ω
Connector Type: PH2.0-3P
Product Size: 30mm * 22mm (1.18inch * 0.87inch)
SHIPPING LIST
Analog Current to Voltage Converter x1
Digital Sensor Cable 3pin
Sản Phẩm Liên Quan
HOT
HOT