Khuôn Silicone 15 Ô Hình Gấu Xinh Xắn Theo Phong Cách Hàn Quốc
151.700
₫ 100.300
Sản phẩm Khuôn Silicone 15 Ô Hình Gấu Xinh Xắn Theo Phong Cách Hàn Quốc đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 151.700 xuống còn ₫ 100.300, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Product name: bear silicone mold
Product size: as shown in figure
Steps for the production of aroma gypsum:
1: prepare 100g gypsum powder, 35g water (30-35 g water)
-pour water into gypsum and stir it quickly and evenly.
-stir the plaster into the mold.
-shake the mold up and down, drain bubbles, and scrape off the surface with a scraping board.
-can be demodeled in about 30-60 minutes.
-can be polished, oil drip, color, and decorated after demodeling.
Ps: gypsum powder recommended imported white porcelain powder, fine powder, zero formaldehyde.
Pigments are recommended to use iron oxide powder or imported acrylic pigments, which are high saturation and do not fade without fear of water or matte.
Essential oils are recommended to use aromatic therapy grade essential oils, high concentration, no alcohol added, dilution water.
Method of making drip glue:
-soft crystal glue (finished products will be soft) operating methods:
L prepare containers for use and clean and dry molds.
2: 1-gage the required components of a and b crystal glue and heat group a to 40°Add group b around c, pour into the container, stir evenly, and remove bubbles.
3. after defoaming, glue is evenly dropped on the mold, such as a small cup or syringe, such as the edge of the mold crystal glue does not flow (basically can walk), can be moved by a small needle to make the glue evenly coated on the surface.
4 gel curing: coated mold, gel time about room temperature 25°The curing time of c3 hours is about 36 hours room temperature.Or put the finished mold in 60°C in the thermostatic drying box, 3 hours is completely cured.。
-operation of hard thermosetting crystal gel (hard-finished products):
1 before configuration, prepare for the same.
2. weigh the components a and b of the required crystal glue with a 3: 1 gage. stir well and drop onto the mold.
3 gel firm: put the finished label in the oven 60°C add about 1.5 hours to the temperature and place about 13 hours at normal temperature.
*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·**·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·
Opening of the new shop, with a focus on civility:
Now, the next collection is concerned with this shop,
I.e. access to r
Product size: as shown in figure
Steps for the production of aroma gypsum:
1: prepare 100g gypsum powder, 35g water (30-35 g water)
-pour water into gypsum and stir it quickly and evenly.
-stir the plaster into the mold.
-shake the mold up and down, drain bubbles, and scrape off the surface with a scraping board.
-can be demodeled in about 30-60 minutes.
-can be polished, oil drip, color, and decorated after demodeling.
Ps: gypsum powder recommended imported white porcelain powder, fine powder, zero formaldehyde.
Pigments are recommended to use iron oxide powder or imported acrylic pigments, which are high saturation and do not fade without fear of water or matte.
Essential oils are recommended to use aromatic therapy grade essential oils, high concentration, no alcohol added, dilution water.
Method of making drip glue:
-soft crystal glue (finished products will be soft) operating methods:
L prepare containers for use and clean and dry molds.
2: 1-gage the required components of a and b crystal glue and heat group a to 40°Add group b around c, pour into the container, stir evenly, and remove bubbles.
3. after defoaming, glue is evenly dropped on the mold, such as a small cup or syringe, such as the edge of the mold crystal glue does not flow (basically can walk), can be moved by a small needle to make the glue evenly coated on the surface.
4 gel curing: coated mold, gel time about room temperature 25°The curing time of c3 hours is about 36 hours room temperature.Or put the finished mold in 60°C in the thermostatic drying box, 3 hours is completely cured.。
-operation of hard thermosetting crystal gel (hard-finished products):
1 before configuration, prepare for the same.
2. weigh the components a and b of the required crystal glue with a 3: 1 gage. stir well and drop onto the mold.
3 gel firm: put the finished label in the oven 60°C add about 1.5 hours to the temperature and place about 13 hours at normal temperature.
*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·**·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·*·
Opening of the new shop, with a focus on civility:
Now, the next collection is concerned with this shop,
I.e. access to r
Sản Phẩm Liên Quan
HOT
Bikini hàng Âu
₫ 400.000
HOT
Bikini Thái quả ngang chấm bi
₫ 350.000
HOT
Bikini made in Thailand
₫ 350.000
HOT
Bikini Thái
₫ 300.000
HOT
Bikini OKISS- QCXK
₫ 400.000
HOT
Bikini xuất Âu
₫ 300.000