Điều Khiển Từ Xa Wifi Cho Bo Mạch Chủ Tft28 Mks Series
561.000
₫ 449.000
Sản phẩm Điều Khiển Từ Xa Wifi Cho Bo Mạch Chủ Tft28 Mks Series đang được mở bán với mức giá siêu tốt khi mua online, Vừa được giảm giá từ 561.000 xuống còn ₫ 449.000, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
Direct use on for MKS series motherboard
(1)Connect WiFi ule to aux-1 interface
(2)Find WiFi hotspots and connect
1. The search hotspot is hi-link-xxx, and the password is 12345678.
2. If the hotspot is not found, press and hold the button on the ule for 10 seconds to restore the factory settings.
3. In particular, by default, the baud rate of WiFi ule is 115200, and the firmware baud rate must be set to the same.
(3) Configure WiFi ule
1. After adding the hotspot hi-link-xxx. Link address: http://192.168.16.254 Enter the configuration page.
2. Login account is admin, password: admin
3. According to the needs of the network configuration, can be ified to the client e
(4) Using printrun to control printer remotely
Note that the IP address of WiFi is 192.168.16.254:8080
(5) Remote control of printers using repeter host
Pay attention to the TCP / IP connection of the connection terminal
Product Name: for MKS hlkwifi ule
Type: hlk-wifi (rm04) WiFi ule
Support motherboard: for MKS + TFT series
WiFi ule products for open source 3D printers. It can be used on the MKS TFT Press screen.
Special note: Based on the strong and stable hlk-rm04 ule development.
Suitable for: can be used in MKS tft28 and all MKS series motherboards (Note: due to insufficient current, it can not be used in ramps1.4 package and for MKS ramp1.4 package)
Material:PCB board
colour:Photo Color
Package Contents:
1 * WiFi ule
1 * Connecting wireOnly the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1
(1)Connect WiFi ule to aux-1 interface
(2)Find WiFi hotspots and connect
1. The search hotspot is hi-link-xxx, and the password is 12345678.
2. If the hotspot is not found, press and hold the button on the ule for 10 seconds to restore the factory settings.
3. In particular, by default, the baud rate of WiFi ule is 115200, and the firmware baud rate must be set to the same.
(3) Configure WiFi ule
1. After adding the hotspot hi-link-xxx. Link address: http://192.168.16.254 Enter the configuration page.
2. Login account is admin, password: admin
3. According to the needs of the network configuration, can be ified to the client e
(4) Using printrun to control printer remotely
Note that the IP address of WiFi is 192.168.16.254:8080
(5) Remote control of printers using repeter host
Pay attention to the TCP / IP connection of the connection terminal
Product Name: for MKS hlkwifi ule
Type: hlk-wifi (rm04) WiFi ule
Support motherboard: for MKS + TFT series
WiFi ule products for open source 3D printers. It can be used on the MKS TFT Press screen.
Special note: Based on the strong and stable hlk-rm04 ule development.
Suitable for: can be used in MKS tft28 and all MKS series motherboards (Note: due to insufficient current, it can not be used in ramps1.4 package and for MKS ramp1.4 package)
Material:PCB board
colour:Photo Color
Package Contents:
1 * WiFi ule
1 * Connecting wireOnly the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1
Sản Phẩm Liên Quan
HOT
Bikini hàng Âu
₫ 400.000
HOT
Bikini Thái quả ngang chấm bi
₫ 350.000
HOT
Bikini made in Thailand
₫ 350.000
HOT
Bikini Thái
₫ 300.000
HOT
Bikini OKISS- QCXK
₫ 400.000
HOT
Bikini xuất Âu
₫ 300.000