Phụ Kiện Mở Rộng 2 Pin Lead Anet A8 A6 A2 Cho Máy In 3d
₫ 46.000
Sản phẩm Phụ Kiện Mở Rộng 2 Pin Lead Anet A8 A6 A2 Cho Máy In 3d đang được mở bán với mức giá siêu tốt khi mua online, giao hàng online trên toàn quốc với chi phí tiết kiệm nhất,0 đã được bán ra kể từ lúc chào bán lần cuối cùng.Trên đây là số liệu về sản phẩm chúng tôi thống kê và gửi đến bạn, hi vọng với những gợi ý ở trên giúp bạn mua sắm tốt hơn tại Pricespy Việt Nam
It very often that after purchasing 3D printer (especially in Anet A8, A6, A2) motherboard is getting all load to heat up Printing Hotbed. That creates fire hazard problems as connectors are not suitable for that high loads.
Hence that issue MOSFET ule is soing existing problems by taking the load off the motherboard.
It also soing print quality issues as motherboard is not heavily overloaded with power consumption of heating printbed.
It is used not for hotbed only. It is very common that it is used for extruder's heating elements too.
MAinly it is to take the load off the motherboard and make motherboard more stable and power interference free.
Color: Black
Material: plastic
If your total power usage is 240W and you have 12V power supply, then it means at least 20A is needed (20X12=240W).
As controller board is only capable of 15A this setting will not work. To make it work, you need this extra power ule.
This ule can be used in both Chitu motherboard, and other open 3D Printer motherboards.
This ule under normal cooling is found stable work situation at I (Max) = 25A, the using current should not exceed 25A.
If you intend to use heated bed with your 3D printer that uses a 12V power supply, then this ule is recommended, else it may cause excessive current during times which may burn the connectors on the controller board.
Anet A8,A6,A2 Compatible.
Package Contents:
1 x MOSFET expansion ule
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1
Hence that issue MOSFET ule is soing existing problems by taking the load off the motherboard.
It also soing print quality issues as motherboard is not heavily overloaded with power consumption of heating printbed.
It is used not for hotbed only. It is very common that it is used for extruder's heating elements too.
MAinly it is to take the load off the motherboard and make motherboard more stable and power interference free.
Color: Black
Material: plastic
If your total power usage is 240W and you have 12V power supply, then it means at least 20A is needed (20X12=240W).
As controller board is only capable of 15A this setting will not work. To make it work, you need this extra power ule.
This ule can be used in both Chitu motherboard, and other open 3D Printer motherboards.
This ule under normal cooling is found stable work situation at I (Max) = 25A, the using current should not exceed 25A.
If you intend to use heated bed with your 3D printer that uses a 12V power supply, then this ule is recommended, else it may cause excessive current during times which may burn the connectors on the controller board.
Anet A8,A6,A2 Compatible.
Package Contents:
1 x MOSFET expansion ule
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1